Seven tricks to help you solve paint problems
&Nbsp; paints are an important part of Interior, prone to some tough questions, make a loss. Actually, just to find out the real cause of the problem, the remedy is not difficult to have satisfactory results, paint is easy to produce problems, proposed solutions, and makes you more handy in Interior. Peeling paint may surface too smooth sake. Original quality of paint or powder coating is light (with untreated color coating), the new paint will not adhere on the surface on prison. Or possibly wood rot or rust metal, there is peeling because of poor paint quality. Small areas of peeling paint, start with fine sandpaper and PuTTY on a wipe, paint primer, then paint. All large areas of peeling paint must be removed, again brushing. Paint blistering first, bubble pricked, if water come out, that is, the infiltration of moisture behind or under the paint layer, scorched by the Sun, the water evaporates into vapor, will paint up into bubbles. At this time, use a hot air gun to remove blistered paint, let the wood dry and paint primer, then paint over the entire patch on the surface again. If the bubbles in the water, may be cracking the wood grain, with a small amount of air, scorched by the Sun, air expands, paint up. Faced with this situation, first scrape off bubbling paint and resin fillers filled cracks, paint on the back, or no fill, after you scrape off the paint, coat microporous paint directly. This cracks the case mostly use chemical paint remover or hot air gun will paint out, then painted. If faults too small when sanding block or wet or dry sandpaper available water, grinding the paint to break on the surface polished after, spread PuTTY, paint primer, and paint again. Bleed paint a too thick, which will cause the flow. While paint is not yet dry, with small brush paint brush, and if the paint was dry, you want to stay dry, the paint surfaces sanded smooth with fine sandpaper, brush the surface clean, then wipe clean with a damp cloth, and then external coats of paint, careful not to brush too thick. Stains paint stains on the surface for many reasons. ≫> Guangzhou cleaning company for example: latex paint water dissolved substances on the walls and rust paint, use steel wool to clean the wall surface will produce rust spots, within the walls of underground pipe leak stains and other. To prevent stains, you can brush a layer of aluminum powder primer, if the stain has occurred, you can remove stains latex paint, brush after the primer layer with aluminium powder, coated all over again. Mildew discoloration such problems occur in wet paint surfaces, such as condensation in glass or metal surfaces often have a dark brown stain. Available fungicides, according to manual instructions handling mouldy parts, after treating the fungus killed, cleaned the surface, and then paint again. Tarnished because no primer or primer and paint not directly on the paint, resulting in lost gloss varnish is absorbed by the wood. Poor paint quality is also a factor. Use wet or dry sandpaper rub off old paint, brush sanding dust, wipe the surfaces with a clean damp cloth, dry, brush on paint all over again. Pay special attention to is, in an environment of very low temperatures painted, paint film dries, may lose its lustre. Paint film, usually due to the first paint is dry brush arising out of the second. Lower solvent affects the top layer of paint in the paint to make it wrinkle. The chemical removal of mercury available agents or heat to remove wrinkled coating, painting again. Remember, be sure to wait for the first time after the paint dried, only on a second time. Rough surface for the new paint finish-rough, usually with a paint brush is not clean or by the surrounding environment. Or it could be paint mixed with patent leather, in use prior to settling and filtering, or stained with dust when the paint is dry. To prevent these problems, you must use a clean paint brush and paint bucket. Old paint before use, be sure to use a paint filter filter paper or a clean nylon stockings. In addition, the painted surfaces when paint is dry use covers or cardboard hidden to prevent stained with dirt. If coarse finish, waiting for them to dry, after the smooth, wipe with wet or dry sandpaper, brush again with paint. Pay special attention to paint must be clean. Appear dark spots on the surface may be painted wood knots before the paint is not sealed, scorched by the Sun, wood heating, resin exudation resulting from wood Festival. Used a scraper to paint, then with fine sandpaper to reveal after the wood, paint will seal the wood section until dry, then paint. Paint won't dry indoor air is bad or the temperature is too low, paints dry slowly. It is possible to open all doors and Windows to promote ventilation, or put a heater in the room to increase the room temperature.
Prev: Sofa cleaning and glazing maintenance
Next: Cleaning procedures and criteria